Flushing a tank and descaling a tankless: water heater upkeep explained

Why a tank water heater needs flushing, what descaling does for a tankless unit, what is safe to do yourself and how the yearly plumbing check helps.
A tank water heater gets flushed to drain the sediment that settles on its bottom. A tankless water heater gets descaled to clear mineral scale from its heat exchanger. Both jobs help the heater keep working the way it should.
The two jobs sound alike, but they are different tasks on different equipment. This guide explains each one, what you can safely do yourself, and where our Northern Colorado plumbing services come in.
Why does a tank water heater need flushing?
Minerals and grit in the water settle to the bottom of the tank over time. That layer, called sediment, sits between the burner or heating element and the water. Flushing drains it out through the valve near the bottom.
When sediment builds up, you may notice:
- Popping or rumbling sounds while the heater runs, as water trapped under the sediment boils and bubbles up.
- Less hot water than before, because sediment takes up room in the tank.
- Cloudy or gritty water at a hot tap.
- A slow or clogged drain valve when you try to drain the tank.
A sediment flush works like this. The heater is turned off or set to its vacation or pilot setting. The cold water supply is shut off. A hose runs from the drain valve to a floor drain or outside. The tank drains, then the cold supply is opened in short bursts to stir up and rinse out what is left. Once the water runs clear, the tank is refilled before the heat goes back on.
Many tank heaters sit in a drain pan, a shallow tray that catches drips. A flush is a good time to check the pan for water. Water in the pan can mean a leak at a fitting, the relief valve or the tank itself.
What does descaling a tankless heater do?
Descaling pumps a cleaning solution through a tankless heater's heat exchanger to dissolve mineral scale. Scale narrows the passages the water flows through, which can cut hot water flow and make the unit work harder.
A tankless water heater heats water as it flows instead of storing it in a tank. It has no tank to collect sediment, so it is never flushed the way a tank heater is. Instead, the minerals can stick to the inside of the heat exchanger as scale.
Signs a tankless unit may need descaling:
- Hot water that runs warm, then cold, then warm again.
- Lower hot water flow at the taps.
- An error code on the unit's display that points to scale or flow.
- New noises from the unit while it heats.
Descaling usually uses isolation valves installed on the water lines at the heater. A small pump circulates the cleaning solution through the unit for a set time, then the unit is flushed with clean water. Some tankless units also have an inlet screen that traps debris and needs cleaning. The maker's manual gives the steps and the cleaning product for your model.
How often either job is needed depends on your water and how much hot water your home uses. Your heater's manual is the first place to look, and a plumber can tell you what they see inside.
Can I do it myself?
Some homeowners flush a tank heater themselves, but it involves scalding water, gas or electric controls and an old drain valve. Descaling needs isolation valves, a pump and the right solution. When in doubt, have a plumber do it.
Before you try a flush yourself, know the risks:
- Hot water burns. Water in the tank can be hot enough to scald. Let it cool before you drain it, and keep children and pets away.
- Old drain valves fail. A plastic drain valve that has not been opened in years can crack or refuse to close. Have a plan for shutting off the water.
- Never heat an empty tank. Heating a tank that is not full can damage the burner or the elements. Refill it before the power or gas goes back on.
- Gas controls need care. If you have a gas heater and are not sure how to relight it, stop and call.
If you smell gas near a gas water heater, stop. Leave your home now. From outside, call your gas company and the fire department. Then call us.
If the heater is leaking from the tank itself, a flush will not fix it. A leak from the tank usually means the heater needs replacing. A leak from a fitting or the relief valve can often be repaired. Shut off the water supply to the heater and call us.
Is the flush part of the Basic Care plumbing check?
Yes. Basic Care members get a plumbing check once a year, and the tank flush is part of it (A $99 value). The plan costs $9.99/month and adds yearly heating and AC checks too.
During that check, the water heater is flushed as part of the yearly plumbing check. It is also a chance to ask about the drain pan, the relief valve or any noises you have heard. Members get priority scheduling, and they can cancel at any time.
If you have a tankless heater, tell us when you book so we know what equipment to expect. Our Northern Colorado plans page lists everything Basic Care includes. If you are still deciding between a plan and one-time visits, the compare page sets the options side by side.
Master plumber Jimi Knight is on our team, and our trip fee is always $0. If your water heater is making noise, running short or leaking, call (970) 585-7776, or start with our plumbing services page.
Need Help?
Contact us today to discuss your needs. Our team is ready to help.
About the Author
Founder, U.S. Army veteran
More Articles
View All PostsReady to Get Started?
Whether you need a repair, maintenance, or a new installation, our expert team is here to help.

